Hobby & Collectables store with the theme Wires, plugs, switches

Contents 100 pieces. 66 plugs and 34 sockets. The quantities of each color are based on average needs.

Can be used for all ROCO rail systems. Low energy consumption, shut off mechanism, 4 single-pole double-throw switches. Can also be installed horizontally. Dimensions approx. 60 x 27 x 45 mm.

The relay has 4 single-pole switches. The contacts have a 2 amp capacity. The relay can be activated by a control box, circuit track, contact track, reed switch, or digital decoder.

Change over button with feedback.

Change over button with feedback for single-slip turnouts and symmetric three-way turnouts. These two turnout designs require – if properly controlled – connections for the four possible turnout positions. The switch 10526 offers a definite control of the three permissible turnout settings. Additional switches can be connected side-by-side.

A pack of 12 pieces

Longer connecting cable for the 6088 and 60880 s 88 decoders. Length 200 cm / 78-3/4".

The feeder wire set comes with interference suppression and overload protection. It includes a circuit board with spade connectors for C Track and a red and a brown feeder wire. One feeder wire set is needed for each conventional track circuit. One 74046 feeder wire set should be installed in each track power circuit to protect against possible radio and television interference caused by locomotives in operation. This feeder wire set also offers effective protection against overloads and short...

Signal control box for the 70361, 70381, 70391, 70392, 70411, 70412, and 70421 semaphore/target signals and for the 764xx series color light signals. This control box is for operating up to 4 signals. A multi-conductor cable with plugs is included for connecting control boxes together.

For four solenoid-operated articles (turnouts, signals, relays) without automatic end-position switch-off. Without feedback. Electrically separated for different circuits.

All of the connections on this control box have the new plugs and sockets.Plugs to work with this control box are included.This control box works in the same manner as the 7272 control box.

All of the connections on this control box have the new plugs and sockets.Plugs to work with this control box are included.This control box works in the same manner as the 7274 control box.

For example in reversing loops

8-pole connector, e.g. for 10777.

Single action button for uncoupling tracks.Use this unit wherever power must be supplied for a short time. The individual buttons are electrically insulated and thus they can operate different power circuits.

This rectifier is for bridging opposite direction operation for signal blocks, reverse loop safeguarding, etc. It is not suitable for Selectrix operation!

With built-in reed switch, to be actuated by means of a 42256 magnet.This potential-free switching contact can be installed at any point of a track layout. The size and colour of the sleeper goes with the ROCO LINE-track, thus camouflaging the contact.Can also be used as feedback-momentary contact along with feedback module 10787 or detector 10808.

This set is for older color light signals (item nos. 7239 to 7242) and semaphore signals (item nos. 7039 to 7042), which come equipped for operation with K or M Track. The set includes center rail insulators, wires for connections, and hardware for one signal block.

2-pole connecting cable with mounted rail clips for ROCO LINE tracks.This cable has no interference suppressor units (EMC) and may only be used for halting sections in front of signals etc. Please use 42421/42521 as the feeder track.

20 contacts, can be separated at any point

A package comes with 10 pieces.

A package comes with 10 pieces.

A package comes with 10 pieces.

A package comes with 10 pieces. These sockets can be used with the standard plugs and sockets from the 71400 assortment.

A package comes with 10 pieces.

For Märklin

To insulate joints and to mark cables. Contracts strongly under influence of heat, hot air.

To insulate joints and to mark cables. Contracts strongly under influence of heat, hot air.

To insulate joints and to mark cables. Contracts strongly under influence of heat, hot air.

To insulate joints and to mark cables. Contracts strongly under influence of heat, hot air.

For the new Märklin standard

Single conductor. Red. 10 m / 390". 0.19 sq. mm / 0.0003 sq. in. cross section.

Single pole, this contact is slipped on between the tie strip and the rail.

10 meter

10 meter

With retaining nut 2A, 250V (VDE) DC Base dimensions: 22.5 x 15 mm Thread length: 12 mm

complete with quality bulb, 12-16 V, DC/AC voltage, 55 mA, cable, E 5.5 mm, Ø 8 mm base.

∅ 2.5 mm

∅ 2.5 mm