Hobby & Collectables store with the theme Wires, plugs, switches

Track rectifier bridges over isolating connections in just one direction (for running though signaled sections in the opposite direction) or protecting the ends of hidden sidings. Not suitable for use with digital layouts.

Can be adjusted through a range of about 10 to 35 ohms (Not over 2 watts continuous operation!) By this mean the power to the locomotive is reduced in pre-determined sections of track, as for example down grades, slow zones and station approaches. Not suitable for digital operation.

For operating uncoupler tracks, or momentary power feed to isolated sections.

For the new Märklin standard

This controller (continuous contact) is for color light signals and includes an additional contact that serves as a track current controller for an automatic train control feature.

Single conductor. Red. 10 m / 390". 0.19 sq. mm / 0.0003 sq. in. cross section.

A package comes with 10 pieces.

Diameter 2.5 mm.

This controller is for operating four turnouts, signals or relays (momentary contact).

∅ 2.5 mm

∅ 2.5 mm

∅ 2.5 mm

With 3 electrically isolated pressure clamps. Especially to use when extending the signal and switch connection, but also as a small distributor plate.

All of the connections on this control box have the new plugs and sockets.Plugs to work with this control box are included.This control box works in the same manner as the 7272 control box.

To insulate joints and to mark cables. Contracts strongly under influence of heat, hot air.

To insulate joints and to mark cables. Contracts strongly under influence of heat, hot air.

To insulate joints and to mark cables. Contracts strongly under influence of heat, hot air.

To insulate joints and to mark cables. Contracts strongly under influence of heat, hot air.

complete with quality bulb, 12-16 V, DC/AC voltage, 55 mA, cable, E 5.5 mm, Ø 8 mm base.

All of the connections on this control box have the new plugs and sockets.Plugs to work with this control box are included.This control box works in the same manner as the 7274 control box.

The feeder wire set comes with interference suppression and overload protection. It includes a circuit board with spade connectors for C Track and a red and a brown feeder wire. One feeder wire set is needed for each conventional track circuit. One 74046 feeder wire set should be installed in each track power circuit to protect against possible radio and television interference caused by locomotives in operation. This feeder wire set also offers effective protection against overloads and short...

A package comes with 10 pieces.

A package comes with 10 pieces.

Dual magnetic drive for a maximum of 14 volts AC or DC. To trigger pulse contacts are required. With limit switch.

This controller enables automatic stops and independent startup of trains in a station, etc. The stopping time can be adjusted smoothly. This controller is not suitable for Selectrix operation!

This controller (momentary contact) is for semaphore/target signals, turnouts, uncoupler tracks, and relays and comes with an additional contact that serves as a track current controller for an automatic train control feature.

Is required if many individual supply lines (eg switches, signals, lighting, etc.) have to be connected to a common pole. 2 electrically isolated terminal strips each with 6 pressure terminals, a total of 12 terminals, allowing connection of at least 24 cables!

20 contacts, can be separated at any point

A package comes with 10 pieces. These sockets can be used with the standard plugs and sockets from the 71400 assortment.

10 meter

For Märklin

∅ 2.5 mm

∅ 2.5 mm

With retaining nut 2A, 250V (VDE) DC Base dimensions: 22.5 x 15 mm Thread length: 12 mm

∅ 2.5 mm

∅ 2.5 mm

Single pole, this contact is slipped on between the tie strip and the rail.

10 meter

∅ 2.5 mm

Can be used for all ROCO rail systems. Low energy consumption, shut off mechanism, 4 single-pole double-throw switches. Can also be installed horizontally. Dimensions approx. 60 x 27 x 45 mm.

Signal control box for the 70361, 70381, 70391, 70392, 70411, 70412, and 70421 semaphore/target signals and for the 764xx series color light signals. This control box is for operating up to 4 signals. A multi-conductor cable with plugs is included for connecting control boxes together.

2-pole connecting cable with mounted rail clips for ROCO LINE tracks.This cable has no interference suppressor units (EMC) and may only be used for halting sections in front of signals etc. Please use 42421/42521 as the feeder track.

For example in reversing loops